free shipping on orders over $99 everyday!

Tailgater Tire Table TGMESH

Tailgater Tire Table TGMESH

Item Number:


Brand: Tailgater Tire Table

Estimated ship date:

Qualifies For Free Shipping* All orders over $99

Add-on options

Parked for a spell and need extra work space? Put those tires to work with the TailGater Tire Table. Attach a table to one or all four of your tires to suit your needs. Even the rear spare can act as support to a Tail Gater Tire Table! The tire itself provides stable support for the TailGater Tire Table, regardless of terrain. Need extra support? Simple extend the center retractable leg. Great for the RV, car, truck, or most any tire sized 14" or larger with standard space between the tire and fender. The Tail Gater Tire Table is powder-coated steel that installs in seconds with no tools required or extra parts to worry about. Use it on your next camping adventure, tailgating before the big game, for an instant picnic area while traveling, or anytime you need a tabletop while outdoors. No hitch required. The 23" W x 29" L x 1.5" thick Tail Gater Tire Table stores flat and weighs just under 12lbs. Weight limit is 50 pounds.


  • Stable regardless of ground conditions
  • Retractable leg for extra support
  • Words on Class-A Motorhomes, Travel Trailers, Trucks, SUVs and more
  • Fits most tires sizes 14”-and up
  • If your fender is extremely close to the tire, it may not work
  • No tools requires for installation
  • No hitch required
  • Installs within seconds
  • 23”W x 29”L x 1.5” thick
  • Steel powder coated finish
  • All parts are stored on table not meant to be used as a seat or step


Great for outdoor vehicle adventures:

  • Overland excursions
  • Tailgating of every kind
  • Camping
  • 4-Wheeling
  • Hunting
  • Car trave;
  • Car picnics
  • RV-ing
  • Construction Sites


Install three jam bolts. There are two on the sides that will lock the rear tire support slider in place. The additional one is for the retractable leg located in the channel down the center of the table.

Press the silver push buttons to release each of the two small legs from the storage located on the bottom side of the table.
Insert legs into the square receivers on left and right sides next to the rear tire support slider with the bend in it. The legs will be pointed towards the bottom of the table and the grip tape will be pointed away from the table top towards the bend in the slider.

After installing both legs into their receivers, loosen the jamb bolts on the left and right side and pull rear tire support slider out about 12 inches.

Put rear tire support over the tire and down until the slider rests on the tire.

With one hand on the rear tire support and your thigh on the outside of the table, pull the table snug against the tire and tighten one jam bolt. Repeat the same for the other side.

Leveling from front of table to back can be accomplished by either raising the table and tightening it against the tire, or loosening it on the tire allowing it to be lower at the end. Side to side leveling is accomplished by rotating the table on the tire.

For added strength and stability, release center retractable support leg by depressing the silver push button on the side of the leg storage channel. You will need to reach up under the table to do this. There is a rectangle cut out in the channel located on the top of the table over the silver push button where you can push the leg out while depressing the silver push button if needed.

Angle the retractable leg towards the tire and rest it between the tire and ground which will help to avoid kicking or tripping on it. It can also be put straight up and down. Tighten the jam bolt when the leg is at the desired length.

If your tires are 32” and up, flipping over the rear tire support slider so the bend is down will allow for more grip on the tire.


*TailGater Tire Table is NOT a step or a seat. Using the table as either could result in injury and damage to the table.

*Remove the table before driving.


TailGater Tire Table’s products are fully warranted to the original owner against manufacturers’ defects in materials and workmanship. If a product ever fails due to a manufacturing defect, we will repair it without charge, or replace it, at our option. Repairs due to accident, improper care, or negligence, where we are not at fault, will be performed at a reasonable charge if possible. We want you to be completely satisfied with your purchase.